To reset a Centurion gate motor, first decide which reset you need: clearing a fault, re-learning where the gate opens and closes, or restoring factory defaults. Each does something different, so use the smallest one that fixes the problem.
Start with the power. Centurion’s motors run off their battery and the mains only charges it, so a flat battery or a tripped breaker stops the gate before any setting does.
Keep clear of the gate and leave the mains wiring alone
Centurion’s own safety rules:
- Only run the gate when you can see it and its path is clear. No one may cross the path of a moving gate.
- Never let children play with the gate or its controls.
- Know the manual release. On a D5 Evo, the key opens a small door; turn the thumbwheel clockwise to release the gate and anticlockwise to re-engage it.
- Switching off the isolator or breaker is fine. Leave the charger and mains wiring to a qualified electrician, as Centurion advises.
Check the power and the battery before you reset anything
Without mains, the battery runs down and the motor shuts off to protect it. A D5 Evo or D10 with a screen shows "Battery Low"; a SMART motor shows battery and mains status in Centurion’s MyCentsys Pro app. Centurion’s first step: check that the circuit feeding the motor is switched on.
Power-cycle safely: mains off, battery off, wait, reconnect
A power cycle restarts the controller. Centurion’s rule before any work on the system: cut the power and disconnect the batteries.
- Make sure nobody is near the gate.
- Switch off the mains at the motor’s isolator or the gate’s breaker.
- Open the motor with its key and unplug the battery lead.
- Wait. Centurion’s support steps allow two minutes.
- Reconnect the battery the right way round (red to positive), switch the mains on and lock the motor.
- Test it with a remote while you watch the gate.
Motor stolen or past it? See gate motors supplied and installed.
"Reset" means one of three things, and they don’t do the same job
| Reset | What it does | When |
|---|---|---|
| Clear a fault | Gets the gate going once the cause is fixed | After a warning such as "Max Collisions" |
| Re-learn the limits | Teaches the motor where open and closed are | The gate stops short or overruns |
| Factory defaults | Puts the settings back to Centurion’s defaults | Last, not first |
Clearing a fault. After too many collisions, a D5 Evo shows "Max Collisions" and stops until the next remote press. First put it in manual and check the gate slides easily all the way: Centurion lists stones on the track, seized wheels and a rack pressing down on the motor’s gear.
Factory defaults. On a D5 Evo or D10 with a screen, Reset Options (under General Settings) offers:
- Factory Defaults: settings back to default; remotes and gate limits are kept.
- Delete All Remotes: every remote removed; settings stay.
- Reset All: factory defaults, plus every remote and timer cleared.
Whatever your installer adjusted, such as auto-close, goes back to default. On SMART motors, settings are changed in the MyCentsys Pro app, and menu names vary by model.
Re-learn the limits when the gate stops in the wrong place
Centurion’s fault guide links a gate running past its end points to the origin marker, the magnet on the rack. If it has moved, set the limits again.
On a D5 Evo or D10 with a screen:
- Release the motor, slide the gate to the middle of its travel and engage it again.
- Hold the oblong (enter) button for two seconds.
- Choose the limits menu and follow the screen.
On a SMART motor (D3 SMART, D5 Evo SMART, D10 SMART, D20 SMART), connect MyCentsys Pro over Bluetooth and run its limits wizard.
The gate moves on its own during setup, so keep everyone clear. The end stops must be solid: the motor uses them to confirm its limits.
Add a NOVA remote from the screen, the app or the receiver
A NOVA remote already carries a unique code, so you never open it: the receiver learns it. How depends on your model and controller.
D5 Evo or D10 with a screen:
- Hold the oblong button for two seconds to enter setup.
- Scroll to Remote Controls and choose Add Remote.
- Pick the button’s job, such as Trigger or Pedestrian, and answer the screen’s questions.
- Press the remote button when asked. The screen shows its ID number.
If the remotes menu is locked, first press a remote that already works.
SMART motors: in MyCentsys Pro, tap Remotes, choose the button and its function, press the remote button when asked, and name it.
A separate NOVA receiver: open it and, with the power on, bridge the Learn (J1) pins with the jumper. The red light comes on; press the remote button and it flashes once. Then remove the jumper.
Delete a lost remote straight away, by its ID or its name
A lost remote is a key to your gate, so delete it.
- Screen (D5 Evo, D10): Remote Controls, then Delete Remotes. Delete Remote by ID removes one without needing it, if you noted its ID. Delete Not Present removes remotes unused for a period you set, from one hour to seven days.
- SMART motors: MyCentsys Pro deletes or disables a remote by name.
- A basic separate receiver may not delete one remote. Erase its memory and learn the remotes you still have again.
Want the gate looked after? See our maintenance plans.
MyCentsys Pro sets up a SMART motor; MyCentsys Remote is for every day
MyCentsys Pro is Centurion’s setup app for SMART motors: limits wizard, remotes, battery and mains status, event logs and a settings backup. Centurion says everyday gate access belongs in MyCentsys Remote instead. Centurion’s newer SMART+ motors add Wi-Fi, so an installer can read the logs remotely once you approve it with a one-time PIN.
Small habits that save trouble at the gate
- Label every remote and list who has each one, with its ID or name, as Centurion recommends.
- Keep the manual, or note your model so you can find it on centsys.co.za.
- Check the battery first when the gate slows down or stops.
Old, failing or stolen motor? Get a quote for a new one
If your motor is old, keeps failing or was stolen, WhatsApp us for a new gate motor quote or call 083 659 0957. We fit Centurion and ET Nice motors, chosen for the gate.
A real job: a stolen gate motor replaced with a Centurion D6 Smart, an anti-tamper bracket, a locked steel box and a siren. Or keep the gate on a maintenance plan, so it’s tested on every visit.
Questions people ask
How do I reset my Centurion gate motor?
Start with a safe power cycle: mains off, battery disconnected, a two-minute wait, then reconnect. If the gate stops in the wrong place, re-learn the limits. Factory defaults comes last; on a D5 Evo it keeps remotes and limits but resets every other setting.
How do I program a Centurion gate remote?
On a D5 Evo or D10 with a screen, hold the oblong button for two seconds, go to Remote Controls, choose Add Remote and press the remote button when asked. On a SMART motor, use Remotes in the MyCentsys Pro app.
Why won’t my gate respond to the remote?
Check the remote’s battery first: its light flashes rapidly when it’s flat. Then check the mains, the motor’s battery, the manual release and the safety beams. If the intercom opens the gate but the remote doesn’t, Centurion points to the receiver.
How do I delete a lost remote?
On a D5 Evo or D10, use Delete Remote by ID in the Remote Controls menu; you need its ID, not the remote. On a SMART motor, delete or disable it by name in MyCentsys Pro.
How long does a gate motor battery last?
Centurion says the lead-acid batteries in its motors should give at least three years of normal service. Long power cuts wear them sooner. A gate that slows down, or shows Battery Low with the mains on, points to the battery or the charger.